Product ID:EUTECTOR T FLUX
MSDS Date:06/03/1992
FSC:3439
NIIN:00N047968
MSDS Number: BTYJM

EUTECTIC CORP

40-40 172ND ST
FLUSHING, NY 11358-2799
US

Emergency Phone: 718-358-4000

Info Phone: 718-358-4000

Cage: 72271

EUTECTIC CORP

CHARLOTTE, NC 28273 US

Telephone: 704-527-9800/ 800-221-1433

Cage: 72271

MAY INCL COMPLEX OXIDES OF METALS LISTED IN INGS,

RTECS: 9999999ZZ

CARBON & SILICA. GASEOUS RXN PRODS MAY INCL OZONE,

RTECS: 9999999ZZ

CERTAIN INERT GASES USED AS SHIELDING GASES.

RTECS: 9999999ZZ

POTASSIUM TETRABORATE

CAS: 1332-77-0

OSHA PEL N/K

ACGIH TLV: N/K

POTASSIUM ACID FLUORIDE; (POTASSIUM BIFLUORIDE)

CAS: 7789-29-9

RTECS: TS6650000

OSHA PEL 2.5 MG/M3 (F) (MFR)

ACGIH TLV: 2.5 MG/M3 (F) (MFR)

BORIC ACID

CAS: 10043-35-3

RTECS: ED4550000

OSHA PEL N/K

ACGIH TLV: N/K

WATER

CAS: 7732-18-5

RTECS: ZC0110000

OSHA PEL N/K

ACGIH TLV: N/K

METAL BEING WELDED, PROCESS, PROCS,

RTECS: 9999999ZZ

CONTAMS IN ATM. FUMES & GASES MAY VARY IN FORM &

RTECS: 9999999ZZ

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:INHAL:FUMES ASSOC W/HEATING, WELDING,
BRAZING, SOLDERING/CUTTING METALS CAN BE DANGEROUS TO YOUR HLTH &
OVEREXP CAN CAUSE LUNG DMG &/OR OTHER ORGAN DMG. USE ADEQ VENT TO
KEEP BELOW EXPOS LIMS. KEEP FU MES & GASES FROM BRTHG ZONE - KEEP
WELDER'S HEAD OUT OF FUMES. EYE/SKIN CONT:ARC RAYS & ULTRAVIOLET
(EFTS OF OVEREXP)
Explanation of Carcinogenicity:NOT RELEVANT
Effects of Overexposure:HLTH HAZ:LIGHT CAN INJURE EYES & BURN SKIN.
LIQS USED IN FLUXES & CHEM AIDS MAY CAUSE IRRIT/POSS CHEM BURNS.
HANDLE W/CARE AS SHOWN IN SAFE HNDLG & STOR SECTION. WEAR PROPER
EYE, EAR & BODY PROT. USE CHEM GOGGS, GLOVES & FCSHLD FOR ALL
FLUXES & CHEM AIDS. ELEC SHOCK CAN KILL. INGEST:DANGER! MAY BE
HARMFUL/ (SUPDAT)
Medical Cond Aggravated by Exposure:AGGRAVATION OF PRE-EXISTING
RESPIRATORY OR ALLERGIC CONDITIONS MAY OCCUR IN SOME WORKERS.

First Aid:INHAL:MOVE VICTIM TO FRESH AIR SOURCE. CONT MD & ADVISE ON
INGS LISTED IN MSDS. SKIN:THORO WASH HANDS/AFFECTED AREAS W/SOAP &
WATER TO REMOVE ALL RESIDUE. IF RASH/BURN DEVELS, CONSULT MD.
EYE:THORO FL USH W/WATER FOR AT LST 15 MINS TO REMOVE ALL RESIDUE.
OBTAIN PROMPT MED ADVISE FOR FLUXES & CHEM AIDS. ADVISE MD OF INGS
LISTED IN MSDS. INGEST:CALL MD &/OR LOC POIS CTL CTR. ADVISE OF
INGS.

Flash Point:NON-FLAMMABLE
Extinguishing Media:CO*2, DRY CHEMICAL FOAM TYPE.
Fire Fighting Procedures:USE NIOSH/MSHA APPROVED SCBA & FULL PROTECTIVE
EQUIPMENT . TOXIC FUMES MAY BE PRODUCED.
Unusual Fire/Explosion Hazard:SOME FLUXES & CHEM AIDS MAY GIVE OFF
HYGROGEN CHLORIDE, PHOSGENE & CHLORINE GASES. CANS UNDER PRESS &
FLAMMS MAY EXPLODE. ALL E+C FLUXES ARE NONFLAMM & (SUPDAT)

Spill Release Procedures:IF FLUX/CHEM AID IS ACCIDENTALLY SPILLED,
CONTAIN SPILL, ABSORB & SWEEP UP. FLUSH AREA W/WATER TO APPRVD CHEM
DRAIN. USE APPROP MEASURES TO KEEP AIRBORNE DUST LEVELS CNTND I/A/W
EXPOS LEVELS OF INGS. SEE ALSO SAFE HNDLG & STOR SECTION.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling and Storage Precautions:PLEASE READ & UNDERSTAND THE PRODUCT
LABEL FOR PROPER PROCEDURES & USE.
Other Precautions:TRAIN WELDER TO KEEP HIS/HER FACE AWAY FROM THE
FUME/DUST PLUME. ONE WAY TO DETERMINE FUMES & GASES TO WHICH
WORKERS ARE EXPOSED IS TO TAKE AIR SAMPLE IN WORKER'S BREATHING
ZONE.

Respiratory Protection:IF WORK STATION IS NOT PROPERLY VENTILATED TO
EXHAUST ALL FUMES, VAPORS & DUSTS BELOW RECOMMENDED EXPOSURE
LIMITS, USE A NIOSH/MSHA APPROVED RESPIRATOR.
Ventilation:USE ENOUGH GENERAL VENT & LOCAL EXHAUST AT WORK SITE TO
KEEP ALL FUMES & DUST FROM WORKER'S BRTHG ZONE & GENERAL AREA.
Protective Gloves:CHEMICAL & OIL IMPERVIOUS GLOVES.
Eye Protection:ANSI APVD CHEM TGHT GOGGS & FCSHLD(SUPDT
Other Protective Equipment:ANSI APVD EMER EYE WASH & DELUGE SHWR . USE
FULL PROT EQUIP NORM USED IN WELDING/BRAZING OPS SO AS TO (SUPDAT)
Work Hygienic Practices:ALWAYS WASH HANDS THOROUGHLY AFTER USE. DO NOT
WEAR CONTACT LENSES.
Supplemental Safety and Health
EXPLO HAZ:ARE USED AS DEOXIDIZERS DURING WELDING, BRAZING/SOLDERING
OPERATIONS. REFER TO ANSI Z49.1 FOR FIRE PVNT DURING USE OF WELDING
& ALLIED PROCESSES. EFTS OF OVEREXP:FATAL IF SWALLOWED. EYE PROT
:APPROP FILTER LENS REC FOR SPECIFIC WELDING OPERATION. OTHER PROT
EQUIP:PVNT SKIN CONT.

Appearance and Odor:NONE SPECIFIED BY MANUFACTURER.

Stability Indicator/Materials to Avoid:YES
STRONG ACIDS, CYANIDES, SULFIDES.
Stability Condition to Avoid:NONE
Hazardous Decomposition Products:IN PRESENCE OF WATER & HEAT, FLUXES
MAY GIVE OFF HCL & HF. COMPOSITION & QTY OF FUMES & GASES ARE
DEPENDENT UPON (ING 5)

Waste Disposal Methods:DISPOSE OF IN AN ENVIRONMENTALLY SENSITIVE
MANNER I/A/W FEDERAL, STATE & LOCAL REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.